Grundfos Booster systems
Booster systems
Grundfos Booster systems (contatori e analizzatori) ha una mappa Modbus di 273 registri. Function code usati: 3 (holding register). Tipi di dato: boolean, uint16, uint32. Esempi: Slave minimum reply delay all'indirizzo 1 (FC 3, uint16); Software defined modbus address all'indirizzo 3 (FC 3, uint16); Software defined bit rate all'indirizzo 4 (FC 3, uint16); Auto ack control bits all'indirizzo 5 (FC 3, uint16).
Contatori e analizzatoriDa documento
Mappa registri Modbus
10 registri
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R/W
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R/W
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R/W
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R/W
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R/W
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R/W
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R/W
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R/W
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R
- FC
- 3
- Tipo
- uint16
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R
| Len | Scala | Endian | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 1 | Slave minimum reply delay SlaveMinimumReplyDelay. The minimum reply delay from the slave in ms. Value range: 0-10000, i.e. up to 10 seconds reply delay. This delay is typically used in conjunction with a modem. The delay value is stored in the device and remains after a power-off. The delay set here is added to the internal delay in the device. Default setting: 0. Note that this is not supported by the built-in SoftCIM Modbus RTU. | slave_minimum_reply_delay | 3 | uint16 | 1 | 1 | — | R/W | big | |
| 3 | Software defined modbus address SoftwareDefinedModbusAddress. This register holds the active Modbus address. The default value is 0xE7 (231), and there is normally no need to change this value. Note that for the CIM 200, this value is used only when you set the transmission speed to "Software-defined" on DIP switches SW4 and SW5. Otherwise, the CIM 200 ignores it. | software_defined_modbus_address | 3 | uint16 | 1 | 1 | — | R/W | big | |
| 4 | Software defined bit rate SoftwareDefinedBitRate. Modbus software-defined value for transmission speed. The software-defined value for transmission speed is stored in the device and remains after a power-off. Note that for the CIM 200, this value is used only when you set the transmission speed to "software-defined" on DIP switches SW4 and SW5. Otherwise, the CIM 200 ignores it. | software_defined_bit_rate | 3 | uint16 | 1 | 1 | — | R/W | big | |
| 5 | Auto ack control bits AutoAckControlBits. Used for selecting the behaviour of control bit acknowledgements from the CIM/CIU Control bits are not automatically lowered when accepted by the device. The user must lower the triggered control bit manually before the control bit can be triggered again. Control bits are automatically lowered when accepted by the device. The user does not have to lower it manually. | auto_ack_control_bits | 3 | uint16 | 1 | 1 | — | R/W | big | |
| 9 | Software defined parity SoftwareDefinedParity. Parity setting when using software-defined settings. Note that for the CIM 200, this value is used only when the transmission speed is set to "software-defined" on DIP switches SW4 and SW5. Otherwise, the CIM 200 ignores it. | software_defined_parity | 3 | uint16 | 1 | 1 | — | R/W | big | |
| 10 | Software defined stop bit SoftwareDefinedStopBit. Stop bit setting when using software-defined settings Note that for the CIM 200, this value is used only when the transmission speed is set to "software-defined" on DIP switches SW4 and SW5. Otherwise, the CIM 200 ignores it. | software_defined_stop_bit | 3 | uint16 | 1 | 1 | — | R/W | big | |
| 12 | Watchdog Watchdog. Configuration of watchdog timeout [5; 3600 s], default: Disabled='0', minimum value 5 s • Watchdog is fed whenever the device is addressed by a valid telegram. • An interruption of telegrams for over the timeout activates the watchdog. • Action: The booster is set to Local mode. • Values 1-4: set timeout to 5 s. Values >3600: set timeout to 3600 s. | watchdog | 3 | uint16 | 1 | 1 | — | R/W | big | |
| 13 | Genibus diode off GENIbusDiodeOff. For disabling the CIM 200 or CIM 500 GENIbus LED24) | genibus_diode_off | 3 | uint16 | 1 | 1 | — | R/W | big | |
| 21 | Genibus CRC error count GENIbusCRCErrorCnt. It holds a CRC error counter for the GENIbus connection to the booster. | genibus_crc_error_count | 3 | uint16 | 1 | 1 | — | R | big | |
| 22 | Genibus data error count GENIbusDataErrorCnt. It holds a data error counter for the GENIbus connection to the booster. | genibus_data_error_count | 3 | uint16 | 1 | 1 | — | R | big |
Stai vedendo 10 registri su 273.
La mappa completa è riservata agli utenti registrati. La registrazione è gratuita.